Return to Main

Dallas County Speedway


RELEASE AND WAIVER OF LIABILITY, ASSUMPTION OF RISK AND INDEMNITY AGREEMENT

Participant wishes to participate at Dallas County Speedway, Urbana, MO. IN CONSIDERATION of being permitted to compete or participate in any EVENT and/or being permitted to enter RESTRICTED AREAS (defined as any area requiring special authorization, credentials or permission to enter or any area to which admission by the general public is restricted or prohibited), PARTICIPANT, on behalf of himself or herself and his or her personal representatives, heirs, and next of kin, agrees as follows:

* Inspection of Restricted Areas: PARTICIPANT acknowledges, agrees and represents that he or she will immediately upon entering the RESTRICTED AREAS, and continuously thereafter, inspect the RESTRICTED AREAS, and further agrees and warrants that, if at any time, he or she is in or about RESTRICTED AREAS and feels anything to be unsafe, he or she will immediately advise the officials of such and if necessary will leave the RESTRICTED AREAS and/or refuse to participate further in the EVENT.

* Release From Liability: PARTICIPANT releases, waives, discharges and covenants not to sue the promoters, other participants, racing associations, sanctioning organizations or any subdivision thereof, track operators, track owners, officials, car owners, drivers, pit crews, rescue personnel, any persons in the RESTRICTED AREA, promoters, sponsors, advertisers, owners of the premises used to conduct the EVENT, premises and event inspectors, surveyors, underwriters, consultants and others who give recommendations, directions or instructions or engage in risk evaluation or loss control activities regarding the premises or EVENT and each of them, their directors, officers, agents and employees (herein collectively "RELEASEES") from all liability to PARTICIPANT and/or his personal representatives, assigns or heirs, for bodily injury, death, or property damage that PARTICIPANT may suffer in this EVENT, whether caused by the negligence of RELEASEES or otherwise.

* Agreement to Indemnify and Hold Harmless: PARTICIPANT agrees to indemnify, save and hold harmless RELEASEES from any loss, liability, damage, or cost, including attorney fees, they may incur arising out of or related to his or her participation in the EVENT, whether caused by the negligence of RELEASEES or otherwise.

* Assumption of Risk: PARTICIPANT acknowledges that the activities of the EVENT are very dangerous and involve a substantial risk of serious injury, death and/or property damage and that injuries received may be compounded or increased by negligent rescue operations or procedures of the RELEASEES. PARTICIPANT acknowledges and voluntarily assumes full responsibility for any risk of bodily injury, death, or property damage that may arise out of or is related to the EVENT, whether caused by the negligence of RELEASEES or otherwise.

* Scope of Release: PARTICIPANT agrees that this Release and Waiver of Liability extends to all acts of negligence by RELEASEES, including negligent rescue operations, and is intended to be as broad and inclusive as is permitted by the laws of the State of Missouri. PARTICIPANT agrees that if any portion of the Release and Waiver of Liability is held invalid, the balance shall, notwithstanding, continue in full legal force and effect.

* Venue: This Release and Waiver of Liability shall be construed in accordance with the laws of the State of Missouri. Dallas County, Missouri shall be the sole and exclusive venue for all disputes arising out of or related to this Release and Waiver of Liability or Participant's participation in the EVENT.

Midwest Mods 2018 Rules


For more information call Bill Allen 417-993-0100

No Modifying of Harmonic Balancer.

Carb must have vaccumm ports for testing vaccumm.

FRAMES

Factory production complete full American passenger frames only. Frame rails must extend to a point beyond the base of driverís seat. Rear clip may be fabricated out of tubing. Front and rear pick-up loop required; otherwise bumpers or other pick-up point will be used.

BODIES

SEE IMCA NORTHERN SPORT MODS for rear sail panel rules. Exceptions: no spoilers, no spoiler sides, no nose wings. RULE CLARIFICATION: Bodies :MD3 nose not allowed, no nose wings ,window opening must be a min. of at least 12 inches on all 4 corners. Body may extend 1" past the tire on both sides. Max. deck height 39 inches. Rear Sail Panels: MUST MEET IMCA NORTHERN SPORT MOD RULES. No reverse hood rake.

WHEEL BASE

108 inches. Minimum, 112 inches maximum both sides.

ROLL CAGE

Must consist of continuous hoops not less than one and one-half inches outside diameter and must have a wall thickness of at least .095 inch. Must be frame mounted in at least six (6) places. Body mounted roll cages not acceptable. Must consist of configuration of front and rear hoops connected by tubing on sides or side hoops in a manner deemed acceptable by the inspector. Driverís head must not protrude above cage with helmet on while strapped in driverís seat. Roll cage must have a 3/16-inch inspection hole in non-critical area. Must have at least three (3) horizontal bars at driverís door welded to front and rear of roll cage members.

WEIGHT

Minimum weight is 2500 pounds with driver after race, No tolerance. All lead weight must be mounted securely, with 2 weight clamps & 1/2 inch bolts. Lead must be painted white & have your car number on the lead.

WHEELS

Wheel width must not exceed eight (8) inches. No aluminum wheels. Bead locks allowed on right rear only. Any foam or plastic type mud cover mounted on right side wheels. Inner mud plug on L.R. only.

TIRES

American Racer G-60 only. Tires may be grooved & siped.

DIFFERENTIAL/REAR END

Any passenger car type or truck rear end may be used. No aluminum.Full spools permitted. No quick-change devices allowed. Floater rear ends are allowed.

BRAKES

Disc or drum brakes may be used front and rear. No aluminum disc or brake calipers allowed. Brakes must be operational on all four (4) wheels and must lock up all four wheels during inspection.

FUEL SYSTEMS

Gasoline only. No oxygen bearing additives. No pressurized fuel systems. Fuel cells mandatory. Fuel max. capacity of 22 gallons. Must have new style screw on lip with flapper in top. Fuel cells must be encased in an approved metal container of no less than 20-gauge steel or 1/8 inch aluminum. Fuel cells must be mounted between frame rails as far forward as possible and using four, two (2) inch by 1/8 inch metal straps, two in each direction. Bumper must be equipped with a drag loop extending below bottom of the cell. No electric fuel pumps.

BUMPERS

Bumpers must be used front and rear. Front bumper must be mounted on frame end and be of a semicircle configuration with the bottom loop parallel to the ground. Front bumper must be ten (10) inches high from bottom bar to top of top bar. Material must be one and one-quarter inch minimum, two-inch maximum O.D. steel pipe. Rear bumpers may be constructed of pipe, square tubing, but must not have sharp edges. Rear bumpers and nerf bars must not extend beyond width of rear tire. Bumpers must be able to support car when lifted by wrecker.

SEAT AND SEAT BELTS

Racing seat mandatory. All cars must be equipped with an approved quick release type seat belt and shoulder harness securely fastened to frame and roll cage. Seat belt material should be at least three (3) inches wide AND CANNOT BE OLDER THAN 2 YEARS. Seat and steering wheel may be located to suit driverís taste, but must be kept on left side of car. No center steer.

ENGINE LOCATION

Rear of engine (bellhousing flange) must be at least 72 inches forward from the centerline of the rear axle. The center of the crankshaft must be within two and one-half (2 1/2) inches of centerline of the ball joints.

ENGINE

Stock motor Must be same make as car. MAXIMUM Size of engine block: 350 gm .060 max. 351 windsor ford .060 max. 360 chry. .060 max Harmonic balancer on G.M.min.8 in Smaller engine allowed no stroker engines allowed!!!!!!!!! OEM firing orders cannot be changed No B Hive or high performance valve springs allowed 9 to 1 compression max.

Heads

76 c.c. min.,stock , no performance heads (no double humps,no292,041 castings,, no lt1., no bowtie, no center bolt valve cover, or aftermarket allowed.) No porting or polishing, no screw in studs with shoulder, no guide plates, 194/160 valves max. no 202/160 allowed. 305 heads on 305 only!!!!!!

Camshaft

Hydraulic camshafts only &must pull at least 15 inches of vacuum at 1000 rpm. no tolerance. Hyd. Cam 430 maximum lift at valve, stock 1.5 ratio rockers only no tolerance. No polylocks, No roller cams, no roller tip or roller rockers allowed. Lifters stock type,no Rhoades ,anti pump up ,high revolution, etc.

Crankshaft and Rods

Stock appearing, no light weight no h- beam rods .Press fit rods only, No floating rods,5.7 rod on G.M.max. Aftermarket eagle scat, ect. Stock type ok No lightening of any kind to crankshaft 3.48 stroke max.

Pistons

Flat top 4 valve relief only Hypereutectic 4 valve relief pistons ok. no je, ross or etc. No high performance parts allowed.

TRACK HAS OPTION TO ENFORCE THESE RESTRICTIONS WITH A CUBIC INCH PUMP GAUGE OR BY VISIBLY CHECKING PARTS AND PART NUMBERS. DISQUALIFICATION AND LOSS OF POINTS IF FOUND ILLEGAL.

SHOCKS

One steel, nonadjustable, unaltered shock per wheel only. No external gas ports of any kind (No screws, No Schrader valves, No ports,none) All shock mounts, including screw jack type, must be welded. No external or internal bumpers or stops. No coil over, air, or remote reservoir shocks. No Schrader valves or bladder type valve allowed. Front half of any shock may be shielded. One or all shocks may be claimed per event for $75 each.

FRONT SUSPENSION

FRONT SUSPENSION MUST MATCH FRAME AND BE IN STOCK LOCATION. PARTS MUST BE REPLACEABLE FROM STOCK OEM TYPE PARTS FROM SAME TYPE SUSPENSION EXCEPT UPPER A-FRAME AND A-FRAME MOUNT. TUBE TYPE UPPER A-FRAME MAY BE USED. FABRICATED A-FRAME MOUNT MAY BE USED BUT MUST BE IN STOCK LOCATION. LOWER AFTERMARKET A-FRAME CAN BE USED BUT MUST BE IN STOCK LOCATION. NO FABRICATED SPINDLES. ADJUSTABLE STRUT BARS CAN BE USED ON FRONT END ONLY. NO COIL OVER SHOCKS ALLOWED EITHER FRONT OR REAR. ONE SHOCK PER WHEEL.YOU MAY NOT RUN A DAMPENING SHOCK ABOVE THE REAREND. STEERING BOX MUST BE STOCK OEM TYPE AND BE IN STOCK LOCATION. NO RACK AND PINION STEERING. NO CENTER STEERING. ADJUSTABLE SWAY BARS ALLOWED.

REAR SUSPENSION - TWO OPTIONS

AFTERMARKET THREE LINK DESIGN OR MULTI-LEAF SPRING DESIGN. ALL COMPONENTS MUST BE STEEL. ALL MOUNTS AND BRACKETS MUST BE WELDED OR BOLTED SOLID.YOU MAY NOT RUN A DAMPENING SHOCK ABOVE THE REAREND.

A). THREE LINK DESIGN REQUIREMENTS: MUST USE MINIMUM 16 INCH CENTER TO CENTER OF HEIMS LOWER TRAILING ARMS BOTH SIDES NEEDS TO BE THE SAME, (1/2 INCH TOLERANCE ), NO SWING ARMS. SOLID PULLBARS ARE REQUIRED, NO SPRING BARS, RUBBER BUSHINGS OR ANY TYPE OF TORQUE DEVISE.PULLBAR MUST BE MOUNTED SOLID ( NO RUBBER OR ANY TYPE OF CUSHION IN THE MOUNTING BRACKET) MUST BE LOCATED AT TOP CENTER OF REAR END HOUSING AND REMAIN CENTERED ON HOUSING OVER DRIVE SHAFT(1INCH TOLERENCE LEFT TO RIGHT). MAY USE MINIMUM 23 INCH LONG PANHARD BAR LOCATED BEHIND REAR END HOUSING OR MINIMUM 19 INCH LONG J-BAR MOUNTED TO A STEEL PINION BRACKET. MEASUREMENTS ARE FROM CENTER OF HEIM JOINT TO CENTER OF HEIM JOINT. MAY MOUNT REAR SPRING DIRECTLY OVER AXLE HOUSING OR USE COIL COVER ELIMINATORS (SLIDERS). LOWER SPRING PERCH OR COIL COVER MOUNT MUST BE WELDED TO REAR END HOUSING. NO BIRDCAGES OR FLOATING MOUNTS ALLOWED. MUST USE STEEL UPPER WEIGHT JACK IF SPRING ARE MOUNTED OVER AXLE HOUSING. NO SHOCK TYPE ELIMINATORS.

DRIVE SHAFT

Any steel approved OEM passenger car or truck non-cambered rear end allowed, must be centered in chassis. All components must be steel, except lowering blocks, axle cap, and drive flange. Safety hubs (floater) allowed. No quick-change devices. Inspection hole in housing required. Mini-spools only. Ring gear, center section and yoke cannot be lightened. Solid steel axles and one piece drive flanges only.

CARBURETOR

4412 HOLLEY NO MODIFACTIONS. EXCEPT JETS AND REMOVED / NOT CHOKE TOWER. CARB. IS SUBJECT TO CLAIM BY ANY DRIVER IN A FEATURE IN LEAD LAP. CLAIM IS 250 DOLLARS OUTRIGHT OR 175 DOLLARS EXCHANGE . FAILURE TO SELL /POINTS AND FINISH FOR THE NIGHT , 2WEEKS SUSP. ,AND 50 DOLLAR FINE PAID TO CHARITY OF RACERS CHOICE BEFORE RETURNING TO RACING/ NO ELECTRIC FUEL PUMPS / MANUEL ONLY. SPACER PLATE FOR CARB. FROM INTAKE TO CARB. ONLY/ CLAIM $25 OUTRIGHT /$15 EXCHANGE.

OIL PANS

Extra capacity oil pans are permitted. No dry sumps allowed. Oil pump must mount in stock position. MUST HAVE 1 INCH INSPECTOIN HOLE ABOVE OIL LEVELFOR INSPECTION. Inspection Hole needs to be installed in a manner were tech official can see crankshaft & rods for proper inspection. If not pan will be removed for inspection.

STARTER

Engine must have working starter and must be capable of starting car on demand.

TRANSMISSION

Option 1 - All forward and reverse gears must be operational, plus a neutral position. With engine running and car in still position, driver must be able to engage car in gear and move forward, then backward. Only OEM production transmissions allowed. No Ďin and outí boxes or quick-change devices allowed. Functioning shift levers must be in OEM location. One steel or aluminum OEM style/size flywheel allowed, must be bolted directly to end of crankshaft.10.4 IN MIN. CLUTCH STOCK APPEARING PRESSURE PLATE MUST WEIGH MIN. OF 15 LBS.Pressure plate will be weighed by itself.STOCK SPRING TYPE DISC NO SOLID HUB. A MIN. OF 15 LB.Flywheel will be weighed by itself.Must be unaltered three or four speed in OEM production case. No five (or more) speeds allowed. Must have working clutch inside explosion-proof steel bell housing with one hole for throw out bearing lever or hose, must be 270 degrees around top of clutch and flywheel area ,NO MINI-CLUTCH ALLOWED.NO RACING CLUTCHES. Components must rotate, consistent with engine rpm, while car is in any gear. No Bert, Brinn, or Falcon type transmissions allowed.

Option 2 - Stock automatic transmission with full size working torque convertor No Power Glides,3 Spd Automatics only no TCI CNR, ETC. TYPE TORQUE CONVERTORS Mandatory must have approved scattershield constructed of minimum 0.125 inch by three inch steel, 270 degrees around flexplate. Only external lines allowed are for transmission cooler. Claim on torque convertors $75.00

DRIVE SHAFT

Minimum two-inch diameter, white, steel drive shaft. Steel slip-yokes only. 360-degree drive shaft loop required and must be constructed of at least .25-inch by two-inch steel, or one-inch tubing, mounted six inches back from front U-joint.

BATTERY

All batteries must be mounted in a safe manner. Top of battery must be covered.

HELMETS & FIRE SUITS

Helmets are required and must be worn at all times car is on the track. All drivers must wear fire suits of a flame-retardant nature. Two-piece suits are allowed. Fire resistant gloves are mandatory. Fire resistant boots are highly recommended.

EXHAUST

Any collector type header allowed. Exhaust must be directed away from areas of possible fuel spillage. No zoomies.No 180 degree headers No step down or y type headers.

KILL SWITCH, FIRE EXTINGUISHER, WINDOW NET

A kill switch is required within easy reach of the driver. This switch must be clearly marked OFF and ON. Weights and/or loose objects are not allowed in the driverís compartment. All cars must be equipped with quick release type window net on driverís door. No rear view mirrors of any kind. No radio communication or sound equipment of any kind.

GAUGES/ELECTRONICS

Mandatory MSD 8728 Soft Touch Control Box .Max. rpm. Chip 6200 required (driver may run less than 6200) Drivers supply own chips.12-volt ignition system only. HEI distributor only. OEM firing order cannot be changed. Ignition rotor, cap, coil and module must remain OEM appearing. No ignition boxes, remote coil or accessories. All wiring must be visible for inspection. Only gauges allowed are analog oil pressure and water temperature and analog tachometer (memory recall allowed). No electronic traction control ALLOWED.

Intake manifold

Only intakes allowed ,gm2101, ford 2121 or 2181 , chrysler2176 or 3776 / intake must be unaltered.






This site designed and maintained by Cyber Candy Media ģ.
Site Copyright © Dallas County Speedway ģ All Rights Reserved.
All referenced brand and product names are trademarks, registered
trademarks or service marks of their respective holders.